Ingredients · release 2026.1

DG-0010: Faba Bean concentrate

Vicia faba (NCBI taxon 3906). Protein 57.5% w/w as supplied (nitrogen factor 5.38, the factor in use when its dispersions were made; faba bean now uses 5.50). Not every assay was run on this ingredient; the gaps are listed below.

The IPI, MPI and MEM results describe protein extracts the Data Garden made from this concentrate in its lab, one per route, not the concentrate as supplied. They show what its protein can do once extracted.

All Faba Bean

Extraction yields

ExtractRouteProtein recovered, % (isolated / input protein)Protein recovered, % (isolated / total input material)
DG-0010-IPI IPI isoelectric precipitation 71.0 ± 0.900 40.9
DG-0010-MPI MPI micellar isolation 38.3 ± 0.400 22.0
DG-0010-MEM MEM membrane concentration 75.6 ± 0.200 43.5

Protein bands (SDS-PAGE)

Which proteins make up the extract, and how large are they?

Protein entries: UniProt (CC BY 4.0). Structures: biological assemblies from the RCSB Protein Data Bank (Berman et al., 2000; CC0) where the protein has one of its own, otherwise the AlphaFold Protein Structure Database (Jumper et al., 2021; Varadi et al., 2024; CC BY 4.0). Each structure links to its entry. Copied 2026-10-27.

DLS - Particle Size v5.0

How large are the particles the protein forms in water? How it is measured

Particle size (% of intensity) by hydrodynamic diameter, intensity (as measured); all runs
0 2 4 6 8 10 nm 100 nm 1 µm

IPI, isoelectric precipitationMPI, micellar isolationMEM, membrane concentration Hover a peak for its size and the run count.

Mean ± SD (n replicates).

MetricUnitDG-0010-IPIDG-0010-MPIDG-0010-MEM
Particle size (hydrodynamic diameter) (early measurement) nm 256 ± 30.6 (n=2)314 ± 3.90 (n=3)167 ± 2.79 (n=2)
Polydispersity index (early measurement) % 22.2 ± 2.44 (n=2)19.2 ± 3.24 (n=3)28.7 ± 0.290 (n=2)
  1. Measured on the dispersion filtered at 0.45 um before the reading, as the method requires. This sample's early runs measured without filtering (April 2026) are withheld from the values and curves; the instrument workbook under raw/ still holds them.Applies to DG-0010-IPI: Particle size (hydrodynamic diameter), Polydispersity index.

DSC - Differential Scanning Calorimetry v5.0

At what temperature does the protein denature, if at all? How it is measured

Thermogram (W/g) heat flow per gram against temperature, baseline-corrected so curves overlay (a straight line through 45-50 °C and 113-118 °C subtracted); endothermic down
-0.03 -0.02 -0.01 0 0.01 45 °C 60 °C 75 °C 90 °C 105 °C

IPI, isoelectric precipitationMPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; hover a point for its value.

Denaturation onset temperature (°C) by ingredient and route
74 76 78 80 82 Faba Bean concentrate

IPI, isoelectric precipitationMPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Denaturation peak temperature (°C) by ingredient and route
85 87.5 90 92.5 95 Faba Bean concentrate

IPI, isoelectric precipitationMPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Denaturation enthalpy (J/g) by ingredient and route
0 1 2 3 Faba Bean concentrate

IPI, isoelectric precipitationMPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Denaturation enthalpy per gram of protein (J/g protein) by ingredient and route
0 5 10 15 Faba Bean concentrate

IPI, isoelectric precipitationMPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Mean ± SD (n replicates).

MetricUnitDG-0010-IPIDG-0010-MPIDG-0010-MEM
Denaturation peak temperature °C 86.1 ± 0.658 (n=2)89.2 ± 0.202 (n=3)93.6 ± 0.260 (n=3)
Denaturation onset temperature °C 75.9 ± 1.72 (n=2)78.4 ± 0.102 (n=3)79.8 ± 0.630 (n=3)
Denaturation enthalpy J/g 1.96 ± 0.332 (n=2)2.89 ± 0.0610 (n=3)1.23 ± 0.0637 (n=3)
Denaturation enthalpy per gram of protein J/g protein 6.26 (n=2)13.4 (n=3)10.3 (n=3)

Emulsion Capacity (Centrifugation) v5.1

How much of an oil and water mix does the protein turn into emulsion, and does it survive heating? How it is measured

Emulsion layer, before heating (pale, behind) and after heating (% of height) by ingredient and route
36 38 40 42 Faba Bean concentrate

IPI, isoelectric precipitation Pale bar behind: emulsified layer before heating (measured, % of the column); solid bar: the layer after 30 min at 80 °C, derived as capacity × heat stability ÷ 100, replicate by replicate. Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Emulsion heat stability (% of layer) by ingredient and route
75 80 85 90 95 Faba Bean concentrate

IPI, isoelectric precipitation Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Mean ± SD (n replicates).

MetricUnitDG-0010-IPIDG-0010-MPIDG-0010-MEM
Emulsion capacity % of height 40.9 ± 0.451 (n=3)2
Emulsion heat stability % of layer 91.1 ± 3.86 (n=3)2
  1. Measured under an earlier version of the emulsion capacity method (April 2026: 4 mL oil to 4 mL dispersion, centrifuged at 3000 rpm for 25 minutes at 20 °C). Not directly comparable with later measurements.Applies to DG-0010-IPI: Emulsion capacity, Emulsion heat stability.

Emulsion Kinetics (Turbiscan) v5.0

How does an emulsion made with these proteins change over the course of an hour? How it is measured

Emulsion stability over time (TSI) Turbiscan stability index against time; a higher index is a less stable emulsion
0 5 10 15 20 0 min 10 min 20 min 30 min 40 min 50 min

IPI, isoelectric precipitationMPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; hover a point for its value.

Turbiscan Stability Index by ingredient and route
15 16 17 18 19 20 Faba Bean concentrate

IPI, isoelectric precipitationMPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Creaming index (% of height) by ingredient and route
0 10 20 30 Faba Bean concentrate

IPI, isoelectric precipitationMPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Mean ± SD (n replicates).

MetricUnitDG-0010-IPIDG-0010-MPIDG-0010-MEM
Creaming index % of height 16.9 ± 1.27 (n=3)39.24 ± 1.68 (n=3)319.2 ± 0.973 (n=3)3
Turbiscan Stability Index 1 15.8 ± 1.07 (n=3)317.4 ± 2.04 (n=3)316.7 ± 0.585 (n=3)3
  1. Measured under an earlier emulsion stability procedure, with the homogenizer vial held by hand; the current method (version 5.0) holds the vial stationary in a stand. The oil load was not recorded. Not directly comparable with measurements made in the stand.Applies to DG-0010-IPI, DG-0010-MEM, DG-0010-MPI: Creaming index, Turbiscan Stability Index.

Foaming Capacity v5.0

How much foam does the protein make, and how much of it is left after 30 minutes? How it is measured

Foam capacity (% of liquid height) by ingredient and route
120 140 160 180 200 Faba Bean concentrate

IPI, isoelectric precipitationMPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Foam stability (% of initial foam) by ingredient and route
72.5 75 77.5 80 82.5 85 Faba Bean concentrate

IPI, isoelectric precipitationMPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Foam height, initial (pale, behind) and final (mm) by ingredient and route
0 10 20 30 Faba Bean concentrate

IPI, isoelectric precipitationMPI, micellar isolationMEM, membrane concentration Pale bar behind: initial height; solid bar: final height. Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Foam capacity by foam stability a dot per extract
120 140 160 180 200 74 74.1 74.2 74.3 74.4 Foam capacity (% of liquid height) Foam stability (% of initial foam)

IPI, isoelectric precipitationMPI, micellar isolationMEM, membrane concentration Crosses: ± SD of each measure; dashed ring: under a caveat; bold outline: on your shortlist.

Mean ± SD (n replicates).

MetricUnitDG-0010-IPIDG-0010-MPIDG-0010-MEM
Foam capacity % of liquid height 146 ± 1.94 (n=3)140 ± 7.04 (n=3)178 ± 4.55 (n=3)
Foam height, final mm 8.87 ± 0.605 (n=3)6.85 ± 0.694 (n=3)15.7 ± 0.988 (n=3)
Foam height, initial mm 12.1 ± 1.88 (n=3)9.28 ± 1.36 (n=3)21.2 ± 1.54 (n=3)
Foam stability % of initial foam 74.1 ± 8.87 (n=3)74.2 ± 3.88 (n=3)74.4 ± 2.07 (n=3)

Gel Strength v5.0

How firm and springy a gel does the protein form when heated? How it is measured

Texture profile (g) force against time over the two compressions
-20 0 20 40 60 0 s 2 s 4 s 6 s 8 s 10 s 12 s

MPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; hover a point for its value.

Gel hardness (g) by ingredient and route
30 40 50 60 Faba Bean concentrate

MPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Gel cohesiveness by ingredient and route
0.5 0.6 0.7 0.8 Faba Bean concentrate

MPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Gel springiness by ingredient and route
0.7 0.75 0.8 0.85 0.9 Faba Bean concentrate

MPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Mean ± SD (n replicates).

MetricUnitDG-0010-IPIDG-0010-MPIDG-0010-MEM
Gel cohesiveness 1 0.773 ± 0.0228 (n=4)0.605 ± 0.00240 (n=2)
Gel hardness g 50.2 ± 5.76 (n=4)33.4 ± 0.888 (n=2)
Gel springiness 1 0.852 ± 0.0197 (n=4)0.731 ± 0.00339 (n=2)

LECO - Protein Content v3.0

How much protein is in the extract? How it is measured

Protein, as is (% w/w) by ingredient and route
0 10 20 30 40 Faba Bean concentrate

IPI, isoelectric precipitationMPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Protein, dry basis (% w/w dry basis) by ingredient and route
80.5 81 81.5 82 82.5 83 Faba Bean concentrate

IPI, isoelectric precipitationMPI, micellar isolation Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Nitrogen (% w/w) by ingredient and route
0 2 4 6 Faba Bean concentrate

IPI, isoelectric precipitationMPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Nitrogen-to-protein factor by ingredient and route
4.5 4.75 5 5.25 5.5 Faba Bean concentrate

IPI, isoelectric precipitationMPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Mean ± SD (n replicates).

MetricUnitDG-0010-IPIDG-0010-MPIDG-0010-MEM
Nitrogen-to-protein factor 1 5.40 ± 0 (n=4)5.40 ± 0 (n=4)5.40 ± 0 (n=4)
Nitrogen % w/w 5.79 ± 0.0670 (n=5)3.99 ± 0.0357 (n=5)2.20 ± 0.00471 (n=5)
Protein, as is % w/w 31.3 ± 0.403 (n=4)21.6 ± 0.210 (n=4)11.9 ± 0.0287 (n=4)
Protein, dry basis % w/w dry basis 81.4 ± 1.30 (n=4)81.0 ± 1.44 (n=2)

Moisture/Ash Content v1.0

How much water and mineral (ash) does it carry? How it is measured

Moisture (% w/w) by ingredient and route
55 60 65 70 75 Faba Bean concentrate

IPI, isoelectric precipitationMPI, micellar isolation Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Ash, dry basis (% w/w dry basis) by ingredient and route
2 2.2 2.4 2.6 Faba Bean concentrate

MPI, micellar isolation Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Mean ± SD (n replicates).

MetricUnitDG-0010-IPIDG-0010-MPIDG-0010-MEM
Ash, dry basis % w/w dry basis 2.46 ± 0.0849 (n=2)
Moisture % w/w 61.5 ± 0.361 (n=6)73.4 ± 0.396 (n=2)

Solubility (Bradford) v5.0

How much of the protein dissolves, and at which pH? How it is measured

Protein in the dispersion, before centrifugation (mg/mL) across pH
0 5 10 15 20 pH 4 pH 5 pH 6 pH 7 pH 8

IPI, isoelectric precipitationMPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; hover a point for its value.

Protein in the supernatant, after centrifugation (mg/mL) across pH
0 5 10 15 pH 4 pH 5 pH 6 pH 7 pH 8

IPI, isoelectric precipitationMPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; hover a point for its value.

Solubility (% of protein) across pH
0 20 40 60 80 100 pH 4 pH 5 pH 6 pH 7 pH 8

IPI, isoelectric precipitationMPI, micellar isolationMEM, membrane concentration Whiskers: ± SD; hover a point for its value.

Readings above 100 % (the assay scatters near full solubility) are shown as 100 %; the downloadable files keep the values as measured.

Mean ± SD (n replicates).

MetricUnitDG-0010-IPIDG-0010-MPIDG-0010-MEM
Protein in the supernatant, after centrifugation, pH 4 mg/mL 0.0960 (n=1)0.508 (n=1)41.01 (n=1)4
Protein in the supernatant, after centrifugation, pH 5 mg/mL 0.370 (n=1)0.972 (n=1)40.788 (n=1)4
Protein in the supernatant, after centrifugation, pH 6 mg/mL 9.19 (n=1)6.81 (n=1)46.99 (n=1)4
Protein in the supernatant, after centrifugation, pH 7 mg/mL 13.2 (n=1)8.03 (n=1)47.88 (n=1)4
Protein in the supernatant, after centrifugation, pH 8 mg/mL 13.2 (n=1)8.15 (n=1)48.03 (n=1)4
Protein in the dispersion, before centrifugation, pH 4 mg/mL 12.4 (n=1)16.9 (n=1)412.4 (n=1)4
Protein in the dispersion, before centrifugation, pH 5 mg/mL 14.3 (n=1)14.0 (n=1)412.9 (n=1)4
Protein in the dispersion, before centrifugation, pH 6 mg/mL 13.3 (n=1)14.5 (n=1)413.0 (n=1)4
Protein in the dispersion, before centrifugation, pH 7 mg/mL 14.2 (n=1)15.1 (n=1)413.5 (n=1)4
Protein in the dispersion, before centrifugation, pH 8 mg/mL 12.5 (n=1)15.2 (n=1)414.3 (n=1)4
Solubility, pH 4 % of protein 0.774 (n=1)3.00 (n=1)48.15 (n=1)4
Solubility, pH 5 % of protein 2.60 (n=1)6.93 (n=1)46.10 (n=1)4
Solubility, pH 6 % of protein 69.1 (n=1)47.1 (n=1)453.8 (n=1)4
Solubility, pH 7 % of protein 93.2 (n=1)53.3 (n=1)458.3 (n=1)4
Solubility, pH 8 % of protein 100 (n=1)53.6 (n=1)456.3 (n=1)4
  1. Measured while the solubility method was still being developed (April 2026). The plate readings were matched to samples and dilutions afterwards from lab records. Read these values with caution until the test is repeated.Applies to DG-0010-MEM, DG-0010-MPI: Protein in the dispersion, before centrifugation, Protein in the supernatant, after centrifugation, Solubility.

Not measured

ExtractAssayReason
DG-0010-MPIECNot measured, and the material cannot be re-run at present.
DG-0010-MEMECNot measured, and the material cannot be re-run at present.
DG-0010-MEMMASHNot measured, and the material cannot be re-run at present.
DG-0010-IPIMASH (ash)Ash not reported: the sample did not ash completely while the furnace procedure was being established, and it was not re-measured.
DG-0010-IPIGELNo gel formed: the dispersion did not set after the 90 °C water bath, and the texture analyzer registered only its trigger force, so there was nothing to measure.

Every replicate is in the data API and in values.csv. Cite the release as Jones, V. P., Moore, I. V., & Westcott, D. (2026). Data Garden plant protein dataset (Version 2026.1) [Data set]. https://doi.org/10.5281/zenodo.23548545