Ingredients · release 2026.1

DG-0016: Lupin isolate

Lupinus spp. (NCBI taxon 3869). Protein 78.8% w/w as supplied (nitrogen factor 6.25, the factor in use when its dispersions were made; lupin now uses 5.46); moisture 5.38%; ash 8.86%.

All Lupin

An isolate is measured as supplied, hydrated in water, not extracted, so it has no extraction yields.

Photos of the extracts (3)

DG-0016-HYD hydrated as supplied

  • DG-0016-HYD: During extraction, 10% gel
    During extraction, 10% gel · 2026-10-08 · color-corrected, as takenThe extraction in progress, at the stage the photo was taken. The gel after heating and cooling, before the texture test.
  • DG-0016-HYD: Final Extract
    Final Extract · 2026-10-08 · color-corrected, as takenThe finished extract as it was stored and sampled for every assay in this dataset.
  • DG-0016-HYD: Solubility
    Solubility · 2026-10-07Tubes after the spin, one per pH. Solubility is the protein measured in the supernatant above the pellet (Bradford) against the dispersion before the spin, so a clear supernatant over a solid pellet reads low.

Photos from the lab, released under the dataset's license. Where marked color-corrected, the photo is adjusted so the four colored tapes and the background look the same in every photo, whatever the light; the photo as taken is linked beside it. Click a photo for the full image.

Protein bands (SDS-PAGE)

Which proteins make up the extract, and how large are they?

Protein entries: UniProt (CC BY 4.0). Structures: biological assemblies from the RCSB Protein Data Bank (Berman et al., 2000; CC0) where the protein has one of its own, otherwise the AlphaFold Protein Structure Database (Jumper et al., 2021; Varadi et al., 2024; CC BY 4.0). Each structure links to its entry. Copied 2026-10-27.

DLS - Particle Size v5.0

How large are the particles the protein forms in water? How it is measured

Particle size (% of intensity) by hydrodynamic diameter, intensity (as measured); all runs
0 2 4 6 8 10 nm 100 nm

HYD, hydrated as supplied Hover a peak for its size and the run count.

Particle size (hydrodynamic diameter); 0.1 M phosphate buffer pH 7, 0.1 % protein (nm) by ingredient and route
10 100 1,000 Lupin isolate

HYD, hydrated as supplied Whiskers: ×/÷ the geometric SD of the replicates (the spread on the log scale); dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order; log scale.

Polydispersity index; 0.1 M phosphate buffer pH 7, 0.1 % protein (%) by ingredient and route
26 28 30 32 Lupin isolate

HYD, hydrated as supplied Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Mean ± SD (n replicates).

MetricUnitDG-0016-HYD
Particle size (hydrodynamic diameter) (0.1 M phosphate buffer pH 7, 0.1 % protein) nm 110 (n=1)
Polydispersity index (0.1 M phosphate buffer pH 7, 0.1 % protein) % 30.8 (n=1)
Polydispersity index (notebook entry, condition not recorded) % 27.9 ± 3.98 (n=3)

DSC - Differential Scanning Calorimetry v5.0

At what temperature does the protein denature, if at all? How it is measured

Thermogram (W/g) heat flow per gram against temperature, baseline-corrected so curves overlay (a straight line through 45-50 °C and 113-118 °C subtracted); endothermic down
-0.002 -0.001 0 0.001 0.002 45 °C 60 °C 75 °C 90 °C 105 °C

HYD, hydrated as supplied Whiskers: ± SD; hover a point for its value.

Denaturation onset temperature (°C) by ingredient and route
80 85 90 95 100 Lupin isolate

HYD, hydrated as supplied Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Denaturation peak temperature (°C) by ingredient and route
90 95 100 105 110 Lupin isolate

HYD, hydrated as supplied Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Denaturation enthalpy (J/g) by ingredient and route
0.14 0.15 0.16 0.17 0.18 Lupin isolate

HYD, hydrated as supplied Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Mean ± SD (n replicates).

MetricUnitDG-0016-HYD
Denaturation peak temperature °C 108 (n=1)1
Denaturation onset temperature °C 98.3 (n=1)1
Denaturation enthalpy J/g 0.172 (n=1)1
  1. Near-flat thermogram: the integrated peak is only about 0.17 J/g. The values stand as measured, but this may not be a real unfolding transition.Applies to DG-0016-HYD: Denaturation enthalpy, Denaturation onset temperature, Denaturation peak temperature.

Emulsion Capacity (Centrifugation) v5.1

How much of an oil and water mix does the protein turn into emulsion, and does it survive heating? How it is measured

Emulsion layer, before heating (pale, behind) and after heating (% of height) by ingredient and route
43.5 44 44.5 45 45.5 Lupin isolate

HYD, hydrated as supplied Pale bar behind: emulsified layer before heating (measured, % of the column); solid bar: the layer after 30 min at 80 °C, derived as capacity × heat stability ÷ 100, replicate by replicate. Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Emulsion heat stability (% of layer) by ingredient and route
85 90 95 100 105 Lupin isolate

HYD, hydrated as supplied Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Mean ± SD (n replicates).

MetricUnitDG-0016-HYD
Emulsion capacity % of height 43.9 ± 1.27 (n=3)
Emulsion heat stability % of layer 100 ± 3.51 (n=3)

Emulsion Kinetics (Turbiscan) v5.0

How does an emulsion made with these proteins change over the course of an hour? How it is measured

Emulsion stability over time (TSI) Turbiscan stability index against time; a higher index is a less stable emulsion
0 5 10 15 20 0 min 10 min 20 min 30 min 40 min 50 min

HYD, hydrated as supplied Whiskers: ± SD; hover a point for its value.

Turbiscan Stability Index by ingredient and route
16 17 18 19 20 21 Lupin isolate

HYD, hydrated as supplied Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Creaming index (% of height) by ingredient and route
6 6.5 7 7.5 8 8.5 Lupin isolate

HYD, hydrated as supplied Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Mean ± SD (n replicates).

MetricUnitDG-0016-HYD
Creaming index % of height 7.59 ± 0.860 (n=3)
Turbiscan Stability Index 1 19.9 ± 0.467 (n=3)

Foaming Capacity v5.0

How much foam does the protein make, and how much of it is left after 30 minutes? How it is measured

Foam capacity (% of liquid height) by ingredient and route
150 160 170 180 190 Lupin isolate

HYD, hydrated as supplied Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Foam stability (% of initial foam) by ingredient and route
50 55 60 65 70 75 Lupin isolate

HYD, hydrated as supplied Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Foam height, initial (pale, behind) and final (mm) by ingredient and route
0 10 20 30 Lupin isolate

HYD, hydrated as supplied Pale bar behind: initial height; solid bar: final height. Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Mean ± SD (n replicates).

MetricUnitDG-0016-HYD
Foam capacity % of liquid height 180 ± 4.19 (n=3)
Foam height, final mm 14.4 ± 0.280 (n=3)
Foam height, initial mm 23.2 ± 2.93 (n=3)
Foam stability % of initial foam 62.8 ± 8.02 (n=3)

LECO - Protein Content v3.0

How much protein is in the extract? How it is measured

Nitrogen-to-protein factor by ingredient and route
4.5 4.75 5 5.25 5.5 Lupin isolate

HYD, hydrated as supplied Whiskers: ± SD; dashed outline and small number: under the caveat of that number (listed below; click the bar to see it); bold outline: on your shortlist. Ingredients in crop order.

Mean ± SD (n replicates).

MetricUnitDG-0016-HYD
Nitrogen-to-protein factor 1 5.46 (n=1)
Nitrogen (powder as supplied) % w/w 12.6 (n=1)
Protein, as is (powder as supplied) % w/w 68.8 (n=1)

Moisture/Ash Content v1.0

How much water and mineral (ash) does it carry? How it is measured

Mean ± SD (n replicates).

MetricUnitDG-0016-HYD
Ash, dry basis (powder as supplied) % w/w dry basis 9.36 (n=1)
Moisture (powder as supplied) % w/w 5.38 (n=1)

Solubility (Bradford) v5.0

How much of the protein dissolves, and at which pH? How it is measured

Protein in the supernatant, after centrifugation (mg/mL) across pH
0 0.2 0.4 0.6 0.8 pH 4 pH 5 pH 6 pH 7 pH 8

HYD, hydrated as supplied Whiskers: ± SD; hover a point for its value.

Solubility (% of protein) across pH
0 2.5 5 7.5 10 12.5 pH 4 pH 5 pH 6 pH 7 pH 8

HYD, hydrated as supplied Whiskers: ± SD; hover a point for its value.

Readings above 100 % (the assay scatters near full solubility) are shown as 100 %; the downloadable files keep the values as measured.

Mean ± SD (n replicates).

MetricUnitDG-0016-HYD
Protein in the supernatant, after centrifugation, pH 4 mg/mL 0.137 (n=1)
Protein in the supernatant, after centrifugation, pH 5 mg/mL 0.0751 (n=1)
Protein in the supernatant, after centrifugation, pH 6 mg/mL 0.617 (n=1)
Protein in the supernatant, after centrifugation, pH 7 mg/mL 0.712 (n=1)
Protein in the supernatant, after centrifugation, pH 8 mg/mL 0.696 (n=1)
Protein in the dispersion, before centrifugation, pH 5 mg/mL 5.14 (n=1)
Solubility, pH 4 % of protein 2.54 (n=1)
Solubility, pH 5 % of protein 1.46 (n=1)
Solubility, pH 6 % of protein 9.38 (n=1)
Solubility, pH 7 % of protein 11.8 (n=1)
Solubility, pH 8 % of protein 12.2 (n=1)

Not measured

ExtractAssayReason
DG-0016 (as supplied)MASH (moisture)Powder as supplied; moisture is not reported for a hydrated isolate. Protein and ash describe the composition.
DG-0016-HYDGELNo gel formed: the hydrated lupin isolate stayed a pourable, deep yellow liquid after the 90 °C water bath, with a few very soft gel fragments floating in it, so no texture measurement was taken.

Every replicate is in the data API and in values.csv. Cite the release as Jones, V. P., Moore, I. V., & Westcott, D. (2026). Data Garden plant protein dataset (Version 2026.1) [Data set]. https://doi.org/10.5281/zenodo.23548545